Hillman Fasteners 190396 5/8-11x1-1/2 Zc Hex Bolt Reviews
Hillman Fasteners 190396 5/8-11x1-1/2 Zc Hex Bolt Feature
- Hillman Fasteners #190396 25PK 5/8-11x1-1/2 Bolt
- HILLMAN FASTENERS
Detail Products
Detail Reviews
Jun 01, 2011 09:07:04
Hillman Fasteners 190396 5/8-11x1-1/2 Zc Hex Bolt
Jun 01, 2011 09:07:04
ROC-8131-520 Mushroom Head Spring Wing Toggle Bolt 3/16 Thd., 3. Long
ROC-8131-520 Mushroom Head Spring Wing Toggle Bolt 3/16 Thd., 3. Long Reviews
#N/A
Detail Products
Detail Reviews
May 31, 2011 12:07:05
Nylon 6/6 Hex Bolt, Slotted Drive, M3-0.5, 6mm Length (Pack of 100)
Nylon 6/6 Hex Bolt, Slotted Drive, M3-0.5, 6mm Length (Pack of 100) Reviews
Nylon 6/6 Hex Bolt, Slotted Drive, M3-0.5, 6mm Length (Pack of 100) Feature
- Hex Bolts feature a chamfered point
- Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
- Hex head for easy driving
- Length is measured from under the head
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads
Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).
Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers.
A threaded fastener's size name includes information about the major external diameter (in millimeters), followed by the thread pitch (millimeters per thread), which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.
Detail Products
- Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M3-0.5, 10mm Length (Pack of 100)
- Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)
- Nylon Hex Bolt, M3-0.5, 6mm Length (Pack of 50)
- Zinc Plated Steel Machine Screw, Flat Head, Phillips Drive, M4-0.7, 25mm Length (Pack of 100)
- Nylon 6/6 Machine Screw, Hex Head, #8-32, 7/8" Length (Pack of 100)
Detail Reviews
May 29, 2011 12:10:05
Century Spring Corp 6Pk 5/32' Od Cmp Spring (Pack Of 5) Springs Compression
Century Spring Corp 6Pk 5/32' Od Cmp Spring (Pack Of 5) Springs Compression Reviews
Century Spring Corp 6Pk 5/32' Od Cmp Spring (Pack Of 5) Springs Compression Feature
- 5/32" OD Compression Spring
- 1-3/8" Height
- .016" Wire Diameter
- .348" Solid Height
- 1.87 LB Maximum Safe Load
Detail Products
Detail Reviews
May 28, 2011 11:01:04
Grade 5 Zinc Plated Steel Hex Bolt, 7/16"-14, 5" Length (Pack of 5)
Grade 5 Zinc Plated Steel Hex Bolt, 7/16"-14, 5" Length (Pack of 5) Reviews
Grade 5 Zinc Plated Steel Hex Bolt, 7/16"-14, 5" Length (Pack of 5) Feature
- Hex Bolts feature a chamfered point
- Zinc Plated Steel fasteners are suitable where strength and corrosion resistance are primary considerations
- Hex head for easy driving
- Length is measured from under the head
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads
Grade 5 fasteners are typically made of medium-carbon steel that is quenched and tempered for added strength. They are commonly used in the automotive industry and other situations in which strength is a moderate concern, and are grade-marked on the head with three radial lines. Steels are designated by a 4 number SAE Steel grade. The first two digits indicate the primary materials used to form the steel. The last 2 digits identify the percentage of carbon for the alloy (in hundredths). The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch). Zinc Plating helps to prevent corrosion.
Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side.
A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.
Detail Products
- Grade 2 Zinc Plated Steel Hex Bolt, 1/4"-20, 1-1/4" Length (Pack of 100)
- Grade 8 Yellow Chromate Alloy Steel Hex Bolt, 1/2"-20, 6-1/2" Length (Pack of 5)
- Zinc Plated Steel Carriage Bolt, Oval Head, 1/2"-13, 6-1/2" Length (Pack of 5)
- Grade 9 Yellow Chromate Alloy Steel Hex Bolt, 1/4"-28, 2-1/2" Length (Pack of 5)
- Alloy Steel Socket Cap Screw, Hex Socket Drive, 1/4"-28, 2-1/4" Length (Pack of 25)
Detail Reviews
May 27, 2011 11:00:05
Grade 5 Zinc Plated Steel Hex Bolt, 1/2"-13, 1-3/4" Length (Pack of 10)
Grade 5 Zinc Plated Steel Hex Bolt, 1/2"-13, 1-3/4" Length (Pack of 10) Reviews
Grade 5 Zinc Plated Steel Hex Bolt, 1/2"-13, 1-3/4" Length (Pack of 10) Feature
- Hex Bolts feature a chamfered point
- Zinc Plated Steel fasteners are suitable where strength and corrosion resistance are primary considerations
- Hex head for easy driving
- Length is measured from under the head
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads
Grade 5 fasteners are typically made of medium-carbon steel that is quenched and tempered for added strength. They are commonly used in the automotive industry and other situations in which strength is a moderate concern, and are grade-marked on the head with three radial lines. Steels are designated by a 4 number SAE Steel grade. The first two digits indicate the primary materials used to form the steel. The last 2 digits identify the percentage of carbon for the alloy (in hundredths). The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch). Zinc Plating helps to prevent corrosion.
Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side.
A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.
Detail Products
- Grade 2 Zinc Plated Steel Hex Bolt, 1/4"-20, 1-1/4" Length (Pack of 100)
- Grade 8 Yellow Chromate Alloy Steel Hex Bolt, 1/2"-20, 6-1/2" Length (Pack of 5)
- Zinc Plated Steel Carriage Bolt, Oval Head, 1/2"-13, 6-1/2" Length (Pack of 5)
- Grade 9 Yellow Chromate Alloy Steel Hex Bolt, 1/4"-28, 2-1/2" Length (Pack of 5)
- Alloy Steel Socket Cap Screw, Hex Socket Drive, 1/4"-28, 2-1/4" Length (Pack of 25)
Detail Reviews
May 26, 2011 15:53:05
Isoplast Flange Bolt, Hex Head, 1/2"-13, 1-1/4" Length (Pack of 25)
Isoplast Flange Bolt, Hex Head, 1/2"-13, 1-1/4" Length (Pack of 25) Reviews
Isoplast Flange Bolt, Hex Head, 1/2"-13, 1-1/4" Length (Pack of 25) Feature
- Flange Bolts feature a built-in washer under the head
- Isoplast is suitable where high strength and chemical resistivity are important
- Hex head for easy driving
- Length is measured from under the head
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads
Isoplast 101 LGF40 NAT is a type of polyurethane developed by Dow Plastics. This particular material has been reinforced with 40% glass fibers, which has the effect of increasing tensile strength to 27,000 psi (pounds per square inch), higher than glass reinforced Peek. Isoplast is also impact resistant, with an Izod Impact Rating of 8 force pounds, which compares favorably to 3 force pounds for Nylon 6/6. Isoplast is chemically resistant, and resists water absorption, retaining only 0.11% weight after 24 hours of exposure. Dielectric strength is 500 volts per millimeter, indicating this material may be suitable as an insulator.
Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side.
A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.
Detail Products
- Brass Hex Bolt, 1/4"-20, 3/4" Length (Pack of 50)
- Grade 9 Yellow Chromate Alloy Steel Hex Bolt, 1/4"-28, 2-1/2" Length (Pack of 5)
- Zinc Plated Steel Carriage Bolt, Oval Head, 3/8"-16, 2-1/4" Length (Pack of 5)
- Steel Cotter Pin, 9/64" Diameter, 2" Length (Pack of 100)
- Grade 5 Zinc Plated Steel Carriage Bolt, Oval Head, 5/16"-18, 3/4" Length (Pack of 5)
Detail Reviews
May 25, 2011 02:03:04
Isoplast Flange Bolt, Hex Head, 1/2"-13, 2-1/2" Length (Pack of 100)
Isoplast Flange Bolt, Hex Head, 1/2"-13, 2-1/2" Length (Pack of 100) Reviews
Isoplast Flange Bolt, Hex Head, 1/2"-13, 2-1/2" Length (Pack of 100) Feature
- Flange Bolts feature a built-in washer under the head
- Isoplast is suitable where high strength and chemical resistivity are important
- Hex head for easy driving
- Length is measured from under the head
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads
Isoplast 101 LGF40 NAT is a type of polyurethane developed by Dow Plastics. This particular material has been reinforced with 40% glass fibers, which has the effect of increasing tensile strength to 27,000 psi (pounds per square inch), higher than glass reinforced Peek. Isoplast is also impact resistant, with an Izod Impact Rating of 8 force pounds, which compares favorably to 3 force pounds for Nylon 6/6. Isoplast is chemically resistant, and resists water absorption, retaining only 0.11% weight after 24 hours of exposure. Dielectric strength is 500 volts per millimeter, indicating this material may be suitable as an insulator.
Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side.
A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.
Detail Products
- Brass Hex Bolt, 1/4"-20, 3/4" Length (Pack of 50)
- Grade 9 Yellow Chromate Alloy Steel Hex Bolt, 1/4"-28, 2-1/2" Length (Pack of 5)
- Zinc Plated Steel Carriage Bolt, Oval Head, 3/8"-16, 2-1/4" Length (Pack of 5)
- Steel Cotter Pin, 9/64" Diameter, 2" Length (Pack of 100)
- Grade 5 Zinc Plated Steel Carriage Bolt, Oval Head, 5/16"-18, 3/4" Length (Pack of 5)
Detail Reviews
May 24, 2011 04:44:08
Galvanized Carriage Bolts 5/16" FGLCBE516X11/2 5/16-18 x 1-1/2
Galvanized Carriage Bolts 5/16" FGLCBE516X11/2 5/16-18 x 1-1/2 Reviews
Galvanized Carriage Bolts 5/16" will really clean up the appearance of your outdoor projects-like deck furniture, decks and docks.
Detail Products
Detail Reviews
May 23, 2011 08:29:03
Class 10.9 Zinc Plated Steel Hex Bolt, M8-1.25, 60mm Length (Pack of 100)
Class 10.9 Zinc Plated Steel Hex Bolt, M8-1.25, 60mm Length (Pack of 100) Reviews
Class 10.9 Zinc Plated Steel Hex Bolt, M8-1.25, 60mm Length (Pack of 100) Feature
- Hex Bolts feature a chamfered point
- Zinc Plated Steel fasteners are suitable where strength and corrosion resistance are primary considerations
- Hex head for easy driving
- Length is measured from under the head
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads
Class 10.9 fasteners are typically made of a medium-carbon alloy steel that is quenched and tempered, with 830 MPa proof load and 1040 MPa tensile strength. It has superior hardness for usage in applications where strength is a primary concern. Steels are designated by a 4 number SAE Steel grade. The first two digits indicate the primary materials used to form the steel. The last 2 digits identify the percentage of carbon for the alloy (in hundredths). The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch). Zinc Plating helps to prevent corrosion.
Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side.
A threaded fastener's size name includes information about the major external diameter (in millimeters), followed by the thread pitch (millimeters per thread), which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.
Detail Products
- Alloy Steel Socket Cap Screw, Hex Socket Drive, M1.6-0.35, 3mm Length (Pack of 50)
- Steel Lock Nut, DIN, M4-0.7 (Pack of 100)
- Class 8.8 Zinc Plated Steel Hex Bolt, M20-2.5, 35mm Length (Pack of 10)
- Grade 8 Yellow Chromate Alloy Steel Hex Bolt, 3/8"-24, 1-3/4" Length (Pack of 5)
- Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M3-0.5, 10mm Length (Pack of 100)
Detail Reviews
May 22, 2011 12:19:04
PFC 3/8"-16 NC x 4-1/2" Grade A Carriage Bolts Hot Dip Galvanized - 50 per Box
PFC 3/8"-16 NC x 4-1/2" Grade A Carriage Bolts Hot Dip Galvanized - 50 per Box Reviews
PFC 3/8"-16 NC x 4-1/2" Grade A Carriage Bolts Hot Dip Galvanized - 50 per Box Feature
- 3/8" Diameter with 16 NC Thread (National Course)
- 4-1/2" Length (Length is measured from under the head)
- Grade A Low Carbon Steel Oval Head Style Carriage Bolt (Meets ASTM A307 & ASME B18.2.1)
- Hot Dip Galvanized (HDG) to meet ASTM A153
- 50 per Box
Detail Products
Detail Reviews
May 19, 2011 07:25:04
Grade 2 Zinc Plated Steel Hex Bolt, 5/16"-18, 2-1/2" Length (Pack of 5)
Grade 2 Zinc Plated Steel Hex Bolt, 5/16"-18, 2-1/2" Length (Pack of 5) Reviews
Grade 2 Zinc Plated Steel Hex Bolt, 5/16"-18, 2-1/2" Length (Pack of 5) Feature
- Hex Bolts feature a chamfered point
- Zinc Plated Steel fasteners are suitable where strength and corrosion resistance are primary considerations
- Hex head for easy driving
- Length is measured from under the head
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads
Grade 2 fasteners are typically made of low-carbon steel and are commonly used for wood and general hardware applications where higher strength is not required. They have no radial markings on the head. Steels are designated by a 4 number SAE Steel grade. The first two digits indicate the primary materials used to form the steel. The last 2 digits identify the percentage of carbon for the alloy (in hundredths). The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch). Zinc Plating helps to prevent corrosion.
Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side.
A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.
Detail Products
- Zinc Plated Steel Carriage Bolt, Oval Head, 3/8"-16, 3" Length (Pack of 5)
- Grade 5 Zinc Plated Steel Hex Bolt, 1/4"-20, 1-1/4" Length (Pack of 5)
- Grade 9 Yellow Chromate Alloy Steel Hex Bolt, 5/16"-18, 1-1/4" Length (Pack of 5)
- Grade 8 Yellow Chromate Alloy Steel Hex Bolt, 3/8"-24, 2-3/4" Length (Pack of 5)
- Grade 5 Zinc Plated Steel Carriage Bolt, Oval Head, 3/8"-16, 4-1/2" Length (Pack of 5)
Detail Reviews
May 18, 2011 12:12:04
Zinc Plated Steel Carriage Bolt, Oval Head, 1/4"-20, 5/8" Length (Pack of 50)
Zinc Plated Steel Carriage Bolt, Oval Head, 1/4"-20, 5/8" Length (Pack of 50) Reviews
Zinc Plated Steel Carriage Bolt, Oval Head, 1/4"-20, 5/8" Length (Pack of 50) Feature
- Carriage Bolts have a domed head with a square neck to prevent spinning
- Zinc Plated Steel fasteners are suitable where strength and corrosion resistance are primary considerations
- Oval head style for recessed finish with a slightly rounded surface
- Length is measured from under the head
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads
Steels are designated by a 4 number SAE Steel grade. The first two digits indicate the primary materials used to form the steel. The last 2 digits identify the percentage of carbon for the alloy (in hundredths). The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch).
Similar to a flat-head style, the oval head style has a slightly convex top surface; it is typically used for appearance.
A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.
Detail Products
- Grade 5 Zinc Plated Steel Carriage Bolt, Oval Head, 3/8"-16, 4-1/2" Length (Pack of 5)
- Grade 2 Zinc Plated Steel Hex Bolt, 1/4"-20, 1-1/4" Length (Pack of 100)
- Stainless Steel Machine Screw, Binding Head, Slotted Drive, #6-32, 3/8" Length (Pack of 100)
- Stainless Steel Machine Screw, Flat Head, Slotted Drive, #4-40, 1/4" Length (Pack of 100)
- Galvanized Steel Carriage Bolt, Oval Head, 5/16"-18, 2-1/2" Length (Pack of 5)
Detail Reviews
May 17, 2011 17:02:04